 |
Dimplex GF20TSN
by mjc121
I have worked for a good few years in a prefabricated set of labs which were built in the 1960s and should have reached the end of their lifespan in 1995. Due to the heating system being as old as the building and not very efficient I got sick of having to light a few Bunsen burners to warm the rooms up. I decided to invest in a small ... electric heater which I could take from room to room with me just, if anything, to take the edge off the cold. This heater was on sale at my local Homebase for £19.99 at the time so I invested in it and took it to work the next day.
The heater
Ok it won't win any design awards but I hardly bought it to look at. The heater is finished in white plastic with a black metal grill at the front. The air intake is on the top so ample room needs to be left above it foe it to work correctly and not over heat. When placed onto a flat surface the grill is tilted upwards at a slight angle - but this is normal for this type of heater.
The grill at the front is fairly large for this type of heater and it has two controls on the top along with a red LED light. These control the heat and speed of the air that is blown out of the front of the heater and the thermostat which turns it off and on again at specific intervals. The heat/speed control can be used on a simple fan setting which will then act as an electric fan and blow air at ambient temperature out of the front.
When set on the 'high' temperature setting the air blown out of the front it surprisingly hot for such a small heater. When left for a few minutes it made a reasonable job of reheating my cup of coffee I had put down on my desk about 15 cm in front of it. (I know a liquid that close to an electric heater - what was I thinking).
On the first use of it there was a faint burning plasticy smell but this is common to all heaters on first use so did not concern me too much. There is an obvious noise to the heater with the fan running but after a while in the same room as it you don't tend to notice it anymore. However, when you come into the room whilst it is running it is obvious it is on. On the 'low' setting the fan is slower so quieter and it is about 1/2 to 2/3 of the heat of 'high'.
The thermostat took a bit of trial and error to get right and I found that sometimes, especially if you have the thermostat set quite high, when the heater goes off it takes a long time for it to switch its self back on. It is probably best to start it off on a low setting so you can override the auto -off by simply turning the thermostat up until the fan kicks in again.
The plastic body of the heater does get quite warm during use, well it is a heater, although the handle stays fairly cool. The big danger is that the metal grill at the front gets very hot. Being metal it stays hot for some time after. I found by switching the heater to just the 'fan' mode it did help to cool it down quicker. The heating element is also very close to the grill this has naturally been done to make the heater as small as possible but to still leave room for the fan. However, just by making it a cm or too larger the element could have been moved back a bit and this may have speeded up the grill cooling down as well.
The big thing was that it did help to take the edge off the cold labs until the inefficient main heating system had had chance to warm the building up. Whilst it would not be much good at heating the whole lab by its self it did keep me warm in my little area of it and this would be ideal for smaller rooms, caravans etc.
This item also carried a BEAB Intertek safety approval.
Specifications
Power 2 KW
Width - 24.6 cm
Depth - 24.3 cm
Height - 11.6 cm (at its high point)
Weight 1.2 kg
Length of flex - aprox 1.7 meters.
Summary:
Well it isn't the nicest looking heater in the world but it did do the job I had bought it for. It helped me keep warmer at work over the colder part of the winter.
Read the complete review |
 |
Argos 2kW Convection Heater
by NotMyToothbrush
For some reason, despite having cavity wall insulation, loft insulation, wall lining insulation, having sealed up every possible draft from outside and turning up the heating the en-suite refuses to stay warm. This means that if we get up in the middle of the night to go to the toilet, we will be sitting in the freezing cold - I swear we ... risk sticking to the toilet seat in the same way your tongue sticks to icy lampposts!
Our last effort to try to fix the problem of little heat in this room when we need to use it at cold times was to buy a heater. We opted for this Argos value heater due to the small investment of just £15 on the item which would mean that if our effort was unsuccessful, we lose less. Luckily, we didn't waste our money. The heater, in a word, was fantastic!
Obviously, this can only be a short time solution to the cold room problem but for the time being, the fact that it switches on very quickly and supplies a large amount of warm air to the room makes it perfect for us. If we leave it for a couple of minutes and return to the en-suite, it will be nice and toasty for us!
It has a very basic design and the designers haven't particularly innovated on the aesthetics in any way, it is as basic as it gets. I buy products to be functional and not pretty so this doesn't bother me. We haven't renovated the en-suite yet after moving into the house 4 years ago so it doesn't stand out in the room for its unattractiveness anyway.
The heater is fairly compact and can be made even more so by wall mounting it. If you do not wish to mount it then you can easily attach the supplied feet using screws to the underside for a very sturdy base.
The heater has a temperature control so that you do not have the room too hot or cold for your needs too. it is very easy to operate via the controls on the side of the device.
A downside to this convection heater, and any convection heater at all, is the phenomenal price of electricity from using it regularly. On full power, this heater is 2KW (2 Units). Using a bit of physics, I can tell you that assume a standard unit price of around 15p for electricity, for each hour that this heater is on, it will cost you 30p. This may not sound like much but say you use it for a total of 1 hour per day, this will then cost you £9 a month just to heat a single room!
Read the complete review |
|
|
Dimplex OPS2GBR
by northernlovely
When I moved into my new home, it didn't have a chimney breast or fireplace and after a year of living there my husband and I decided the lounge needed a focal point. We went for a suite (fire, surround and hearth) to make life a little easier.
**The Dimplex OPS2GBR**
Dimplex is a trusted brand in fires and ... fireplaces and that's why we went for the Dimplex OPS2GBR. The biggest draw for us was the 'optiflame' technology which has to be seen to be believed - it's by far the most realistic flame effect I've seen on an electric fan heater fire.
**Price and Availability**
We bought our Dimplex OPS2GBR at B&W which is a seller of Dimplex fires and sets though I have seen it in Homebase, Argos, and independent fireplace stores. The price varies, however we paid £220 in the sale which I am happy with for a brand name fireplace set.
**Looks**
It comes with a white surround which is quite simplistic and a black backboard which offsets the brass fire nicely. The heater part of the fire (where the controls are) is a matt black and the fire is embellished with real coal. It looks very modern with a touch of traditional, and very cosy. It would go in many styles of house.
Size wise it's a decent, big surround at H85.7 x W92 and D20cm and gives an elegant centre point to any room. It weighs in at 22.8kg, my husband could (just!) carry the box for installation.
**Installation**
Following the instructions provided and with a set of standard DIY tools my husband had the fire installed and done within 2 hours and that included chipping out the skirting board!
I'd say that it's not too difficult to install but obviously it's not for novices, you do need some DIY know how. You don't need to be an electrician though - it plugs in to a standard wall socket.
**Specs**
The Dimplex OPS2GBR has two heat settings (1KW and 2KW) which are turned on through two switches on the front of the hood, the third switch is for the flame effect, which you can run without any heat.
**Use**
It's very, very easy to use - three switches, and it's also very safe, too. My little girl says 'hot' and 'burny' and won't go near it - but it is perfectly safe to touch (I won't be telling her that, though!) as it runs cold on flame effect. The coals light up from below and they actually look like they've heated up and are glowing, it's a lovely effect and strangely warming even when the heat isn't on!
We've had nothing but compliments from visitors, most of whom didn't realise at first that the Optiflame effect isn't real!
**Recommend?**
Yes I absolutely recommend the Dimplex OPS2GBR and any Dimplex fire with the Optiflame effect. It looks great, it's reasonably priced, it's easy to install and the results are amazing.
From having a lounge with no real focal point, to having a warm, cosy feeling lounge with a glowing fire, I'm so happy that we chose the Dimplex OPS2GBR set and I highly recommend it to all.
Read the complete review |
