|
For wireless or voice over IP (VoIP) deployments, the Cisco SFE2010P supports the IEEE 802.3af standard for Power over Ethernet (PoE). Automatic load sensing in the power-control circuitry detects PoE on the end device before providing power. For safety, each port has independent overload and short-circuit protection, along with LED indicators to show power status. The switch provides 15W of available PoE power on up to 24 of the Fast Ethernet ports for powering PoEenabled wireless access points or VoIP handsets. The maximum PoE available per switch for all ports is 360W. The Cisco SFE2010P provides resilient stacking for up to four units, or 192 ports. A stack of units is managed as a single switch with one web management interface. The SFE2010P switch can coexist in a stack with the Cisco SFE2000 and SFE2000P 24-Port 10/100 Ethernet Switches and the Cisco SFE2010 48-Port 10/100 Ethernet Switch, for a maximum of 192 ports in a stack. The stacking capability includes master/backup unit behavior, ring and chain architecture, and hot insertion and removal of units. Software running on the Cisco SFE2010P switch interacts with provisioning, management, and security software on both the site's services router and the service provider's equipment. This interaction provides simple, one-step installation and access to web-administered features for the administrator and users. Simple, affordable network operations throughout the network's lifetime are the result. |
||
Technical Details for Cisco Small Business Managed Switch SFE2010P
PDF - Print the technical details
| General | |
| Device Type | Switch - stackable |
| Enclosure Type | Rack-mountable - 1U |
| Width | 44 cm |
| Depth | 37.5 cm |
| Height | 4.4 cm |
| Weight | 4.9 kg |
| Networking | |
| Ports Qty | 48 x Ethernet 10Base-T, Ethernet 100Base-TX |
| Auxiliary Network Ports | 2x10/100/1000Base-T |
| Max Units In A Stack | 4 |
| Data Transfer Rate | 100 Mbps |
| Data Link Protocol | Ethernet, Fast Ethernet |
| Routing Protocol | IGMPv2, IGMP |
| Remote Management Protocol | SNMP 1, RMON 1, RMON 2, RMON 3, RMON 9, Telnet, SNMP 3, SNMP 2c, HTTP, HTTPS, SSH |
| Connectivity Technology | Wired |
| Communication Mode | Half-duplex, full-duplex |
| Switching Protocol | Ethernet |
| MAC Address Table Size | 8K entries |
| Status Indicators | Link activity, port transmission speed, power, link OK, Unit ID |
| Features | Auto-sensing per device, DHCP support, auto-negotiation, BOOTP support, VLAN support, auto-uplink (auto MDI/MDI-X), IGMP snooping, DoS attack prevention, port mirroring, Weighted Round Robin (WRR) queuing, MAC address filtering, Broadcast Storm Control, IPv6 support, firmware upgradable, SNTP support, Access Control List (ACL) support, Quality of Service (QoS), Jumbo Frames support |
| Compliant Standards | IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.3ab, IEEE 802.1p, IEEE 802.3af, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.1x, IEEE 802.1s |
| Expansion / Connectivity | |
| Expansion Slots Total (Free) | 2 ( 2 ) x SFP (mini-GBIC) |
| Interfaces | 48 x network / power - Ethernet 10Base-T/100Base-TX - RJ-45 2 x network host - Ethernet 10Base-T/100Base-TX/1000Base-T - RJ-45 1 x management - console |
| Miscellaneous | |
| Cables Included | 1 x serial cable |
| Rack Mounting Kit | Included |
| Encryption Algorithm | MD5 |
| Authentication Method | Secure Shell (SSH), RADIUS |
| Compliant Standards | CE, UL 60950, CSA C22.2, FCC CFR47 Part 15 |
| Power | |
| Power Over Ethernet (PoE) | Yes |
| Power Device | Power supply - internal |
| Voltage Required | AC 120/230 V ( 50/60 Hz ) |
| Features | Redundant Power System (RPS) connector |
| Environmental Parameters | |
| Min Operating Temperature | 0 °C |
| Max Operating Temperature | 40 °C |
| Humidity Range Operating | 10 - 90% |



